Here are the answers to Monday's CCNA and CCNP certification training questions!
CCNA:
Short answer: You want to change EIGRP's default assumption that a serial interface is connected to a T1 line. You want to indicate to EIGRP that the line is actually running at roughly 33% of a T1 line capacity. What command will do this, and where should it be placed?
Answer: Enter the bandwidth 512 command under the serial interface's configuration - NOT the EIGRP configuration.
CCNP / BSCI:
Short answer: In the following configuration, what value is represented by "1544"?
R2(config)#router eigrp 100
R2(config-router)#redistribute ospf 1 metric 1544 100 1 255 1500
Answer: Bandwidth. The order of these metrics in the redistribute command when redistributing routes into EIGRP: bandwidth, delay, reliability, load, mtu.
CCNP / BCMSN:
In a typical Network Management block, what switch layers are represented?
A. Access
B. Distribution
C. Core
Answer: A, B. In addition to network management devices, both Access and Distribution switches will be found here.
CCNP / BCRAN:
Identify the true statements regarding CAP and DMT.
A. CAP has over 200 channels.
B. CAP has three channels.
C. DMT has three channels.
D. DMT has over 200 channels.
Answers: B, D. These are both ADSL standards. CAP offers three channels - one each for voice, upstream traffic, and downstream traffic. DMT has 250 separate channels and is considered superior to CAP.
CCNP / CIT:
Which of the following allows the closest DCE to perform loopback testing?
A. TDR
B. BERT
C. volt-ohm meter
D. cable tester
Answer: B. That's the purpose of a Bit Error Rate Tester (BERT).
See you later today with another set of Cisco CCNA and CCNP certification practice questions, plus new articles and tutorials!
To your Cisco certification success,
Chris Bryant
CCIE #12933
http://www.thebryantadvantage.com
CCNA:
Short answer: You want to change EIGRP's default assumption that a serial interface is connected to a T1 line. You want to indicate to EIGRP that the line is actually running at roughly 33% of a T1 line capacity. What command will do this, and where should it be placed?
Answer: Enter the bandwidth 512 command under the serial interface's configuration - NOT the EIGRP configuration.
CCNP / BSCI:
Short answer: In the following configuration, what value is represented by "1544"?
R2(config)#router eigrp 100
R2(config-router)#redistribute ospf 1 metric 1544 100 1 255 1500
Answer: Bandwidth. The order of these metrics in the redistribute command when redistributing routes into EIGRP: bandwidth, delay, reliability, load, mtu.
CCNP / BCMSN:
In a typical Network Management block, what switch layers are represented?
A. Access
B. Distribution
C. Core
Answer: A, B. In addition to network management devices, both Access and Distribution switches will be found here.
CCNP / BCRAN:
Identify the true statements regarding CAP and DMT.
A. CAP has over 200 channels.
B. CAP has three channels.
C. DMT has three channels.
D. DMT has over 200 channels.
Answers: B, D. These are both ADSL standards. CAP offers three channels - one each for voice, upstream traffic, and downstream traffic. DMT has 250 separate channels and is considered superior to CAP.
CCNP / CIT:
Which of the following allows the closest DCE to perform loopback testing?
A. TDR
B. BERT
C. volt-ohm meter
D. cable tester
Answer: B. That's the purpose of a Bit Error Rate Tester (BERT).
See you later today with another set of Cisco CCNA and CCNP certification practice questions, plus new articles and tutorials!
To your Cisco certification success,
Chris Bryant
CCIE #12933
http://www.thebryantadvantage.com
Comments