To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is. The show command for HSRP is show standby, and it's the first command you should run while configuring and troubleshooting HSRP. Let's run it on both routers and compare results.
R2#show standbyEthernet0 - Group 5
Local state is Standby, priority 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.776
Virtual IP address is 172.12.23.10 configured
Active router is 172.12.23.3, priority 100 expires in 9.568
Standby router is local 1 state changes, last state change 00:00:22
R3#show standbyEthernet0 - Group 5
Local state is Active, priority 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.592
Virtual IP address is 172.12.23.10 configured
Active router is local
Standby router is 172.12.23.2 expires in 8.020
Virtual mac address is 0000.0c07.ac05
2 state changes, last state change 00:02:08
R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.
An IP address was statically assigned to the virtual router, but not a MAC address. However, there is a MAC address under the show standby output on R3, the active router. How did the HSRP process arrive at a MAC of 00-00-0c-07-ac-05?
Well, most of the work is already done before the configuration is even begun. The MAC address 00-00-0c-07-ac-xx is reserved for HSRP, and xx is the group number in hexadecimal. That's a good skill to have for the exam, so make sure you're comfortable with hex conversions. The group number is 5, which is expressed as 05 with a two-bit hex character. If the group number had been 17, we'd see 11 at the end of the MAC address - one unit of 16, one unit of 1.
On rare occasions, you may have to change the MAC address assigned to the virtual router. This is done with the standby mac-address command. Just make sure you're not duplicating a MAC address that's already on your network!
R2(config-if)#standby 5 mac-address 0000.1111.2222
1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Active -> Learn
R2#show standby
Ethernet0 - Group 5
Local state is Active, priority 150, may preempt
Hellotime 4 sec, holdtime 12 sec
Next hello sent in 3.476
Virtual IP address is 172.12.23.10 configured
Active router is local
Standby router is 172.12.23.3 expires in 10.204
Virtual mac address is 0000.1111.2222 configured
4 state changes, last state change 00:00:00
1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Listen -> Active
The MAC address will take a few seconds to change, and the HSRP routers will go into Learn state for that time period.
A real-world HSRP troubleshooting note: If you see constant state changes with your HSRP configuration, do what you should always do when troubleshooting - check the physical layer first.
Best of luck on your BCMSN exam!
Chris Bryant
CCIE #12933
We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is. The show command for HSRP is show standby, and it's the first command you should run while configuring and troubleshooting HSRP. Let's run it on both routers and compare results.
R2#show standbyEthernet0 - Group 5
Local state is Standby, priority 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.776
Virtual IP address is 172.12.23.10 configured
Active router is 172.12.23.3, priority 100 expires in 9.568
Standby router is local 1 state changes, last state change 00:00:22
R3#show standbyEthernet0 - Group 5
Local state is Active, priority 100
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.592
Virtual IP address is 172.12.23.10 configured
Active router is local
Standby router is 172.12.23.2 expires in 8.020
Virtual mac address is 0000.0c07.ac05
2 state changes, last state change 00:02:08
R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.
An IP address was statically assigned to the virtual router, but not a MAC address. However, there is a MAC address under the show standby output on R3, the active router. How did the HSRP process arrive at a MAC of 00-00-0c-07-ac-05?
Well, most of the work is already done before the configuration is even begun. The MAC address 00-00-0c-07-ac-xx is reserved for HSRP, and xx is the group number in hexadecimal. That's a good skill to have for the exam, so make sure you're comfortable with hex conversions. The group number is 5, which is expressed as 05 with a two-bit hex character. If the group number had been 17, we'd see 11 at the end of the MAC address - one unit of 16, one unit of 1.
On rare occasions, you may have to change the MAC address assigned to the virtual router. This is done with the standby mac-address command. Just make sure you're not duplicating a MAC address that's already on your network!
R2(config-if)#standby 5 mac-address 0000.1111.2222
1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Active -> Learn
R2#show standby
Ethernet0 - Group 5
Local state is Active, priority 150, may preempt
Hellotime 4 sec, holdtime 12 sec
Next hello sent in 3.476
Virtual IP address is 172.12.23.10 configured
Active router is local
Standby router is 172.12.23.3 expires in 10.204
Virtual mac address is 0000.1111.2222 configured
4 state changes, last state change 00:00:00
1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Listen -> Active
The MAC address will take a few seconds to change, and the HSRP routers will go into Learn state for that time period.
A real-world HSRP troubleshooting note: If you see constant state changes with your HSRP configuration, do what you should always do when troubleshooting - check the physical layer first.
Best of luck on your BCMSN exam!
Chris Bryant
CCIE #12933
Comments