Welcome back! Here are the answers to your free Cisco certification training questions for October 30!
CCENT Certification:
Given the following output, what's the first thing you should check?
Router1#show interface serial 0
Serial0 is down, line protocol is down
Answer: The "down/down" combination indicates a physical problem. Check that cable, even if it looks connected! :)
CCNA Certification:
By default, what values are considered by IGRP and EIGRP when computing a path's metric?
A. bandwidth
B. cost
C. delay
D. load
E. MTU
Answers: A, C. Bandwith and delay are used by default; MTU and load can be used, but are not used by default. Cost is the term used for an OSPF route's metric.
CCNP Certification / BSCI Exam:
Which of the following is NOT one of the activities at the distribution layer of the Cisco Three-Layer Hierarchical Model?
A. traffic filtering
B. internet access
C. policy routing
D. inter-VLAN routing
E. end user interaction with the network
F. route redistribution
G. address aggregation & summarization
Answer: E. End users interact with the network at the Access layer of this model.
CCNP Certification / BCMSN Exam:
What term refers to the process of the switch placing data into the proper egress queue?
A. marking
B. scheduling
C. trusting
D. classification
Answer: B. The term "scheduling" refers to the process of the switch placing data into the proper exit ("egress") queue.
CCNP Certification / ISCW Exam:
Short answer: You're halfway through Setup mode when you realize that you would rather configure the router from the CLI. What keystroke will bring you to the CLI without saving any of the configuration you're created so far?
Answer: CTRL-C. A handy one to know even if you're not working on the CCNP!
CCNP Certification / ONT Exam:
Short answer: What queueing method presents a potential issue known as "packet starvation"? What does this term mean?
Answer: Priority queueing has four queues, named in accordance with the priority given to the packets in them - High, Medium, Normal, Low. PW does not use round-robin, so if too many packets are placed in the higher-priority queues, packets in the lower-priority queues stand a chance of never being serviced properly.
Back later today with new questions!
To your success,
Chris Bryant
CCIE #12933
http://www.thebryantadvantage.com/
CCENT Certification:
Given the following output, what's the first thing you should check?
Router1#show interface serial 0
Serial0 is down, line protocol is down
Answer: The "down/down" combination indicates a physical problem. Check that cable, even if it looks connected! :)
CCNA Certification:
By default, what values are considered by IGRP and EIGRP when computing a path's metric?
A. bandwidth
B. cost
C. delay
D. load
E. MTU
Answers: A, C. Bandwith and delay are used by default; MTU and load can be used, but are not used by default. Cost is the term used for an OSPF route's metric.
CCNP Certification / BSCI Exam:
Which of the following is NOT one of the activities at the distribution layer of the Cisco Three-Layer Hierarchical Model?
A. traffic filtering
B. internet access
C. policy routing
D. inter-VLAN routing
E. end user interaction with the network
F. route redistribution
G. address aggregation & summarization
Answer: E. End users interact with the network at the Access layer of this model.
CCNP Certification / BCMSN Exam:
What term refers to the process of the switch placing data into the proper egress queue?
A. marking
B. scheduling
C. trusting
D. classification
Answer: B. The term "scheduling" refers to the process of the switch placing data into the proper exit ("egress") queue.
CCNP Certification / ISCW Exam:
Short answer: You're halfway through Setup mode when you realize that you would rather configure the router from the CLI. What keystroke will bring you to the CLI without saving any of the configuration you're created so far?
Answer: CTRL-C. A handy one to know even if you're not working on the CCNP!
CCNP Certification / ONT Exam:
Short answer: What queueing method presents a potential issue known as "packet starvation"? What does this term mean?
Answer: Priority queueing has four queues, named in accordance with the priority given to the packets in them - High, Medium, Normal, Low. PW does not use round-robin, so if too many packets are placed in the higher-priority queues, packets in the lower-priority queues stand a chance of never being serviced properly.
Back later today with new questions!
To your success,
Chris Bryant
CCIE #12933
http://www.thebryantadvantage.com/
Comments