Cisco CCNA Exam Tutorial: Configuring Standard Access Lists
I'm going to tell you from experience - you must master access lists if you're going to earn a Cisco certification, or be able to work with Cisco technologies and protocols. Access lists are used to identify traffic for dozens of different Cisco router and switch features, and you're going to see more and more of them as you earn your CCNA, CCNP, and CCIE. Since they use wildcard masks, this is just another reason to get comfortable with binary conversions as well.
Today we're going to take a look at basic ACL theory, particularly that of standard ACLs.
Access Control Lists (ACLs) allow a router to permit or deny packets based on a variety of criteria. An ACL is configured in global configuration mode, but is applied at the interface level. An ACL does not take effect until it is expressly applied to an interface with the ip access-group command. Packets can be filtered as they enter or exit an interface.
If a packet enters or exits an interface with an ACL applied, the packet is compared against the criteria of the ACL. If the packet matches the first line of the ACL, the appropriate “permit” or “deny” action is taken. If there is no match, the second line’s criterion is examined. Again, if there is a match, the appropriate action is taken; if there is no match, the third line of the ACL is compared to the appropriate value(s) of the packet.
This process continues until a match is found, at which time the ACL stops running. If no match is found, a default “deny” takes place, and the packet will not be processed. When an ACL is configured, if a packet is not expressly permitted, it will be subject to the implicit deny at the end of every ACL. This is the default behavior of an ACL and cannot be changed.
A standard ACL is concerned with only one factor, the source IP address of the packet. The destination IP address is not considered. Extended ACLs consider both the source and destination of the packet, and can consider the port number as well. The numerical range used for each is different: standard ACLs use the ranges 1-99 and 1300-1399; extended lists use 100-199 and 2000 to 2699.
There are several points worth repeating before beginning to configure standard ACLs.
Standard ACLs consider only the source IP address for matches.
The ACL lines are run from top to bottom. If there is no match on the first line, the second is run; if no match on the second, the third is run, and so on until there is a match, or the end of the ACL is reached. This top-to-bottom process places special importance on the order of the lines.
There is an implicit deny at the end of every ACL. If packets are not expressly permitted, they are implicitly denied.
If Router 3’s Ethernet interface should only accept packets with a source network of 172.12.12.0, the ACL will be configured like this:
R3#conf t
R3(config)#access-list 5 permit 172.12.12.0 0.0.0.255
The ACL consists of only one explicit line, one that permits packets from source IP address 172.12.12.0 /24. The implicit deny, which is not configured or seen in the running configuration, will deny all packets not matching the first line.
The ACL is then applied to the Ethernet0 interface:
R3#conf t
R3(config)#interface e0
R3(config-if)#ip access-group 5 in
But before you write any ACLs, it's a really good idea to see what other ACLs are already running on the router! To see the ACLs running on the router, use the command show access-list.
R1#show access-list
Standard IP access list 1
permit 0.0.0.0
Standard IP access list 5
permit 172.1.1.1
Standard IP access list 7
permit 23.3.3.3
Extended IP access list 100
permit tcp any any lt www (26 matches)
permit tcp any any neq telnet (12 matches)
deny ip any any
Extended IP access list 105
deny tcp any any eq www
deny tcp any any eq telnet
You're going to use ACLs all the way up the Cisco certification ladder, and throughout your career. The importance of knowing how to write and apply ACLs is paramount, and it all starts with mastering the fundamentals!
To your Cisco certification success,
Chris Bryant
CCIE #12933
www.thebryantadvantage.com
I'm going to tell you from experience - you must master access lists if you're going to earn a Cisco certification, or be able to work with Cisco technologies and protocols. Access lists are used to identify traffic for dozens of different Cisco router and switch features, and you're going to see more and more of them as you earn your CCNA, CCNP, and CCIE. Since they use wildcard masks, this is just another reason to get comfortable with binary conversions as well.
Today we're going to take a look at basic ACL theory, particularly that of standard ACLs.
Access Control Lists (ACLs) allow a router to permit or deny packets based on a variety of criteria. An ACL is configured in global configuration mode, but is applied at the interface level. An ACL does not take effect until it is expressly applied to an interface with the ip access-group command. Packets can be filtered as they enter or exit an interface.
If a packet enters or exits an interface with an ACL applied, the packet is compared against the criteria of the ACL. If the packet matches the first line of the ACL, the appropriate “permit” or “deny” action is taken. If there is no match, the second line’s criterion is examined. Again, if there is a match, the appropriate action is taken; if there is no match, the third line of the ACL is compared to the appropriate value(s) of the packet.
This process continues until a match is found, at which time the ACL stops running. If no match is found, a default “deny” takes place, and the packet will not be processed. When an ACL is configured, if a packet is not expressly permitted, it will be subject to the implicit deny at the end of every ACL. This is the default behavior of an ACL and cannot be changed.
A standard ACL is concerned with only one factor, the source IP address of the packet. The destination IP address is not considered. Extended ACLs consider both the source and destination of the packet, and can consider the port number as well. The numerical range used for each is different: standard ACLs use the ranges 1-99 and 1300-1399; extended lists use 100-199 and 2000 to 2699.
There are several points worth repeating before beginning to configure standard ACLs.
Standard ACLs consider only the source IP address for matches.
The ACL lines are run from top to bottom. If there is no match on the first line, the second is run; if no match on the second, the third is run, and so on until there is a match, or the end of the ACL is reached. This top-to-bottom process places special importance on the order of the lines.
There is an implicit deny at the end of every ACL. If packets are not expressly permitted, they are implicitly denied.
If Router 3’s Ethernet interface should only accept packets with a source network of 172.12.12.0, the ACL will be configured like this:
R3#conf t
R3(config)#access-list 5 permit 172.12.12.0 0.0.0.255
The ACL consists of only one explicit line, one that permits packets from source IP address 172.12.12.0 /24. The implicit deny, which is not configured or seen in the running configuration, will deny all packets not matching the first line.
The ACL is then applied to the Ethernet0 interface:
R3#conf t
R3(config)#interface e0
R3(config-if)#ip access-group 5 in
But before you write any ACLs, it's a really good idea to see what other ACLs are already running on the router! To see the ACLs running on the router, use the command show access-list.
R1#show access-list
Standard IP access list 1
permit 0.0.0.0
Standard IP access list 5
permit 172.1.1.1
Standard IP access list 7
permit 23.3.3.3
Extended IP access list 100
permit tcp any any lt www (26 matches)
permit tcp any any neq telnet (12 matches)
deny ip any any
Extended IP access list 105
deny tcp any any eq www
deny tcp any any eq telnet
You're going to use ACLs all the way up the Cisco certification ladder, and throughout your career. The importance of knowing how to write and apply ACLs is paramount, and it all starts with mastering the fundamentals!
To your Cisco certification success,
Chris Bryant
CCIE #12933
www.thebryantadvantage.com
Comments